ホーム > 商品情報 > ガラスパネルの貼り方(English) How to apply the Glass Panel Screen Protector

商品情報

How to apply the Screen Protector Film

This explains how to apply the Glass Panel.
Also, the manual is downloadable as a PDF file from below link.
⇒The Glass Panel PDF

step1step1

Before applying the the Glass Panel, check the place where it will be attached.

*Please take care not to install the Glass Panel upside down.

step2step2

Use a soft cloth, wipe the whole of LCD screen to remove dirt and dust and clean it.

*Using strong force to wipe the LCD screen may cause damage. Please wipe gently and carefully.

step3step3

Use theattached [A:Dust Removal Sheet] to remove any remaining dust or particles from the LCD screen surface.

*This step is most effective if it is done immediately before attaching Glass panel.

step4step4

Peel off he backing film of the Glass Panel completely.

*Please be careful to avoid touching the adhesive surface as much as possible.

step5step5

Re-confirm the position of the LCD screen and then align the Glass Panel. Attach the Glass Panel slowly, taking care not to let air or dirt get inside.

step6step6

Attach Glass panel naturally, spreading it from the middle towards the outer edges.

*A mottled pattern may remain on the adhesive layer immediately after it isattached, but this will naturally disappear within one to two days.

How to apply the Camera Lens Film

step1

Use a soft cloth and gently clean the camera lens.

step2step2

Peel off one transparent film for camera lense from the backing film and leave the film half peeled off.
Apply adhesive tape (Ex, Scotch tape) to about half of the film for camera lense, and peel it off the backing film.
Use the [ B:Camera Lens Auxiliary sheet ] if included with the product.

*Please note: If you put the auxiliary sheet on the film entirely not partially, it may become difficult to apply.

step3step3

Place the film on the camera lense, which has now been detached from the backing film.
Once you have decided on its position, use one finger to place the film on the camera lens, apply it firmly to the camera lens and then you are ready to go.

What to do in the following cases

one point!
気泡の取り方
If air bubbles are formed:

○Bigger bubbles can be removed by pushing the Glass Panel outward with your finger.

*Please rest assured that small air bubbles without any trapped dust or dirt will naturally disappear within one or two days.

ホコリやチリがはさまった場合

○If large pieces of dust or other material are caught under the Glass Panel, and the bubbles won’t disappear, temporarily lift the Glass Panel.

And then, use adhesive tape to pick up and remove the particles from its adhesive surface.

one point!
ガラスパネルのはがし方
How to peel off the Glass Panel:

(1)Use a fingernail to pick up a corner of the Glass Panel, so it floats upward.

(2)Lift it up slowly, so that air spreads under the entire Glass panel, then peel it away from the LCD screen.

*Lift it up carefully. Lifting it forcefully may damage the Glass Panel.

one point!
貼り位置が合わなかった場合
If the Glass Panel is not affixed
in the right place:

(1)Peel off the Glass Panel carefully as the above instruction.

(2)Hold the edge of the film and affix it again onto your device.

*Hold the product’s edges and reattach it.

商品情報

  • 画面保護フィルム
  • AFP画面保護フィルム3
  • AFP画面保護フィルム2
  • ノングレア画面保護フィルム3
  • ノングレア画面保護フィルムSE
  • AR液晶保護フィルム
  • カバーケース・ホルダー
  • フリーサイズケース
  • 保護フィルムの貼り方
  • 保護フィルムの貼り方
  • ガラスパネルの貼り方

オンラインショップ

法人用リンクバナー

アスデック公式facebookページ

アスデック公式twitterページ

アスデック公式Youtubeチャンネルページ